Therefore if you wish to apply them at a 50mm depth (the normal depth for a driveway) one tonne will cover 14 square metres. For pedestrian pathways, 35mm is normally sufficient in which case 1 tonne will be sufficient to cover approximately 20 square metres.
How do I work out how many tons of stone I need?
Length in feet x Width in feet x Depth in feet (inches divided by 12). Take the total and divide by 21.6 (the amount of cubic feet in a ton). The final figure will be the estimated amount of tons required.
How deep should type 1 be?
It is usual to lay MOT Type 1 at a compacted depth of 100mm for most patio projects and at a compacted depth of 150mm for most domestic driveways. Compaction should be achieved using a wacka plate. MOT Type 1 is used to stabilise the ground prior to laying paving and also allows for drainage.
How Much stone do I need to cover an area?
Consider a ½ cubic foot bag of stone or soil weighs about 50 lbs and will cover 2 square feet at 3″ deep. A bag of hardwood or cedar bark contains about 1 cubic foot of material, enough to cover about 4 square feet at 3″ deep. If you have large areas you probably need bulk.
How much will a ton of stone cover?
A ton of gravel will cover approximately 100 square feet, 2 inches deep.
How much gravel is in a ton?
A ton of gravel with average-sized pebbles is about 0.705 cubic yards, or 19 cubic feet, assuming it has been screened for debris and contains no leftover dirt, sand, etc.
How much does a ton of 2 inch Stone cover?
Using 2 inches for the depth, the following measurements are a guide to the amount of gravel coverage per ton: 1/4 to 1/2 inch gravel, 100 square feet per ton; 1/2 to 1 inch gravel, 90 square feet per ton; and 1 1/2 to 2 inches gravel, 80 square feet per ton.
How many yards is 3 tons?
How many yards is 3 tons?
| Ton Register [ton Reg] | Cubic Yard [yd^3] |
|---|---|
| 3 ton reg | 11.1111111111 yd^3 |
| 5 ton reg | 18.5185185185 yd^3 |
| 10 ton reg | 37.037037037 yd^3 |
| 20 ton reg | 74.0740740741 yd^3 |
Does water drain Type 1?
Mot Type 1 limestone is sized from 40mm down to dust and is mainly used as a bulk fill, a levelling material and as a sub-base for paths, ponds, drives, sheds, patios and construction jobs. MOT Type 1 is permeable so assists with drainage and as it includes the larger stones it won’t easily wash away.
How much does a bulk bag of type 1 cover?
One bulk bag will cover approximately 8 square metres (coverage is calculated assuming a depth of 50mm). Building materials are delivered usually on the same day as your patio/driveway products and are provided by a Simply Paving contracted merchant from your area.
How big is 1 tonne of Type 1 stone?
The guy who ordered my type 1 has his own mini digger and uses the same grabber firm for all his work. 10 sq m at 0.1m depth for a 1 tonne (850kg) bag? It would float on water at that density
How to calculate how much gravel you need for a foundation?
1 Square or rectangular area. To calculate how much gravel you need to cover a rectangular area you need to multiply the volume by the gravel density. 2 Round area covered with gravel. The volume of a figure with a round foundation is its height times the area of its foundation. 3 Irregularly shaped area. …
How can I estimate the amount of stone I Need?
It should help you estimate the amount of stone you will need. The depth will depend on the size of the material as well as its intended use. To calculate an area using our aggregate calculator, first choose the unit of measurement on the left hand side, the default is kilograms and metres but this can be changed to tonnes/feet.
How many inches of crushed stone do you need?
Since we needed 6 inches of crushed stone, we used 0.5 feet for the height (that is, we converted inches into feet). If your number comes out as a fraction — and it probably will — round up.
